EN

S-Plate · S-Parts

Chromium Carbide Overlay Wear Plates & Wear Parts

Bimetallic wear-resistant steel plate with a chromium-carbide hardfacing overlay (our S-Plate), and wear liners, chutes, cones and pipes made from it to your drawing (our S-Parts) — supplied and exported directly to cement, power, steel and mining plants.

S-Plate

S-Plate — Bimetallic Wear Plate

S-Plate has two layers: a mild carbon-steel base and a chromium-carbide alloy overlay applied by automatic hardfacing. The overlay gives high abrasion resistance while the base keeps the plate tough and workable like ordinary steel plate — it can be cut, rolled, bent, welded and bolted into parts to drawing.

  • Automatic powder-fed hardfacing: wire and alloy powder are fed into the weld pool, with travel speed, motion and current tightly controlled.
  • M7C3 chromium carbides evenly distributed through the overlay thickness.
  • Overlay chemistry, thickness and plate size can be adapted to the operating conditions.
S-Plate plates and cut samples
S-Plate plates and cut samples
58–65 HRCoverlay hardness
< 0.15 gmass loss in ASTM G65 (Procedure A)
Up to 25 mmoverlay thickness
1450 × 2950 mmstandard plate size

Supply Options

  • Full-size S-Plate sheets
  • Plates cut to size
  • S-Parts made to drawing or sample
  • Export packing and worldwide delivery

S-Plate Grades

S-Plate 100

S-Plate 100

Standard plate for sliding abrasion by particles and bulk material, with light impact.

Overlay
M7C3 chromium carbide (C 3–5 %, Cr 18–35 %)
Hardness
58–62 HRC
ASTM G65-A wear test
< 0.15 g
Service temperature
Up to 350 °C
Plate size
1450 × 2950 mm
S-Plate 200

S-Plate 200

Chromium carbide plus complex carbides — for severe abrasion and high temperatures.

Overlay
Chromium carbide + niobium and vanadium carbides
Hardness
62–65 HRC
ASTM G65-A wear test
< 0.135 g
Service temperature
Up to 750 °C
Plate size
1450 × 2950 mm
S-Plate S102

S-Plate S102

Smooth, flat surface without weld-bead ridges — resists abrasion and impact, and material build-up.

Overlay
Chromium carbide with uniform, rounded carbides
Hardness
58–60 HRC
ASTM G65-A wear test
< 0.15 g
Surface
Flat, no weld beads, no surface cracks
Plate size
1000 × 3000 mm

Technical Data

PropertyS-Plate 100S-Plate 200S-Plate S102
Overlay chemical composition (wt %)
C3–55.22–5
Cr18–3522.518–35
Si–0.9< 1.2
Mn< 1.50.5< 1.5
B––< 1
Nb–6.8–
V–4.5–
Nb/Mo/Ti/V/W––< 1.2
FeBalanceBalanceBalance
Properties
Surface hardness58–62 HRC62–65 HRC58–60 HRC
ASTM G65 wear test, Procedure A< 0.15 g< 0.135 g< 0.15 g
MicrostructureM7C3 carbides in austeniteAustenite with complex carbidesM7C3 carbides in austenite
Service temperatureUp to 350 °CUp to 750 °C–
SurfaceWeld beadsWeld beadsSmooth, no weld beads
Dimensions
Base steelASTM A36 / SS400 (JIS)ASTM A36 / SS400 (JIS)ASTM A36 / SS400 (JIS)
Thickness base + overlay (mm)5+5, 6+6, 8+5, 10+5, 10+85+3, 6+4, 8+5, 10+5, 10+85+5, 6+6, 8+5, 10+5, 10+8
Maximum overlay thicknessUp to 25 mm on requestOn requestUp to 25 mm on request
Standard size (W × L)1450 × 2950 mm1450 × 2950 mm1000 × 3000 mm

Specifications can be adjusted on request. Values are for reference; a detailed data sheet is provided with the quotation.

Uniform Hardness Through the Overlay

Hardness measured through the overlay of an S-Plate S102 10+10 stays at about 61–63 HRC and drops only close to the transition to the base steel.

40506070109876543210Distance from base steel (mm)Hardness (HRC)
Cross-section: carbide overlay on base steel
Cross-section: carbide overlay on base steel
Overlay microstructure
Overlay microstructure

Abrasion Resistance Test — ASTM G65

The sample is pressed against a rotating rubber wheel while a stream of abrasive sand flows between them; abrasion resistance is measured as the mass lost by the sample.

Standard
ASTM G65, Procedure A
Load
130 N (30 lb)
Wheel revolutions
6000
ASTM G65 abrasion test apparatus
ASTM G65 abrasion test apparatus

Comparative Results

SampleInitial mass (g)Mass after test (g)Mass loss (g)
Sample 1 — structural steel (ordinary base steel)86.67485.2201.454
Sample 2 — standard wear-resistant hardfacing (flux-cored wire)173.512173.4710.041
Sample 3 — wear-resistant hardfacing with covered electrodes127.642127.3490.293

Workable Like Steel Plate

S-Plate can be plasma cut, rolled, bent, welded and bolted (stud welding or drilled holes) like ordinary steel plate.

Automatic overlay welding line
Automatic overlay welding line
Rolling into curved liners
Rolling into curved liners
Bending and welding into pipe bends
Bending and welding into pipe bends
Stud welding for bolted fixing
Stud welding for bolted fixing

S-Parts

S-Parts — Ready-Made Wear Parts

S-Parts are wear parts fabricated from S-Plate to the customer’s drawing or sample and delivered ready to install — as replacement and spare parts for equipment.

Benefits

  • Makes full use of S-Plate wear resistance to protect equipment
  • Lower cost than hardfacing directly on the equipment
  • Plannable maintenance and replacement
  • Lower spare-parts inventory cost

Part Types

  • Liners
  • Cones
  • Hoppers
  • Chutes
  • Pipes & bends
  • Blades & rings

Typical Parts

Roller-shaft cover for a Loesche vertical roller mill
Roller-shaft cover for a Loesche vertical roller mill
Rolled roller-shaft cover segments
Rolled roller-shaft cover segments
Sliding-block liners for a Polysius raw mill
Sliding-block liners for a Polysius raw mill
Material guide vanes for a vertical mill
Material guide vanes for a vertical mill
Lined cones installed at a plant
Lined cones installed at a plant
Mill body liners
Mill body liners
Lined pipe bends for material transport
Lined pipe bends for material transport
Static separator blades
Static separator blades
Chute liners
Chute liners
Material feed pipes
Material feed pipes
Main chute
Main chute
Coal hopper cones for a power plant
Coal hopper cones for a power plant

Typical Applications

  • Cement
  • Coal-fired power
  • Steelmaking
  • Mining
  • Machinery manufacturing
  • Guide vanes
  • Mill body liners
  • Roller and roller-shaft covers
  • Dam rings
  • Wear rings and slide rings
  • Fan blades
  • Conveying and dust pipes
  • Feed and diverter hoppers
  • Material inlets
  • Screen plates
  • Chute, silo and truck-body liners

Photos show actual S-Plate and S-Parts products and parts installed at customer plants.

Information for a Quotation

  • 01S-Plate grade, base + overlay thickness, plate size and quantity
  • 02For S-Parts: drawing, or photos with main dimensions
  • 03Operating conditions: abrasive material, temperature, impact
  • 04Quantity, required date and delivery destination (port, country)

Discuss Your Next Sourcing or Manufacturing Project with Us

Send us your drawings or 3D data and our team will guide you through the technical review.

Request a Quote